Instructions. Before using your Joyetech AIO for the first time, make sure the battery is fully charged. Connect your AIO Kit to a computer using the USB charging cable included in the pack; you'll know when it's charged as the button light will go out.
it depends on charging source, from typical usb port it should take 3~4 hours. Make sure you are using free usb hub there's no other devices connected in the same row. You can always unplug it and get couple puffs.
Your Joyetech eGo AIO battery's life will vary depending on usage. The AIO has a 1500mAh battery, which is above average capacity for a pen-style kit. A light vaper should find that their battery will last around a day or more; heavier vapers may need to recharge more often than this.
If you don't prime your coil and you heat the wick dry, it can cause it to burn straight away, giving you that nasty dry puff taste. Priming a new coil is easy. Before you put the coil in your tank, you need to saturate the wick by dripping a small amount of e-liquid down each of the coil holes.
Heavy vapers require a change every five to seven days. Moderate vapers can use coils for up to two weeks. If you are a light vaper, your coil will serve you for a maximum of four weeks.
With a higher airflow, the clouds will be cooler to feel, but by cooling it down, you lose a bit of flavor. Instead of forcing the flavor out with the vapor, it can stay on the coils. Higher airflow can decrease the amount of juice needed, because it remains on the coils.
A light crackling pop noise is a completely predictable and usual process. This is an e-juice being heated by the coil and vaporizing, and it means a good sign that your e-cig works properly. When you vape, your e-liquid hits a very hot coil and turns it into a vapor. This reaction makes you hear a crackling noise.
Of course you can 'over prime' it. If you put in too much liquid then it'll just flood. If the coil is installed in the tank base then the juice will sit under the coil by the airflow holes, you'll have leaking and heavy spitting when vaping.
When a dry hit occurs, it can ruin your taste for the day, irritate your throat, and it will almost certainly ruin your coil head.
Letting dirty coils soak and having water pass through them will remove some of the residue, but not all of it. And on top of that, you will need to wait for water to fully evaporate, which may take a while. If you still want to clean your coil heads, then you can follow the old soak and rinse method.
It does have the potential to damage it, but if it makes it through, it should taste cleaner. Again let it dry thoroughly before use. If there is cotton in your vape then you should avoid vaping a burnt coil. It may cause breathing issues because of burnt cotton.
eGo AIO has a 15 second run time protection. The light will flash 10 times if the button is pressed for more than 15 second. Low voltage protection: When the battery voltage drops lower than 3.3V, the button light flashes for 40 times and the device will power-off.
How to Operate Joyetech ESPION Solo?
- Power on/off: Hold the mod and pull the magnetic cell cover to open.
- Vaping. Hold the fire button and inhale through the mouthpiece.
- Lock/ unlock. You can lock the screen by clicking the function button to avoid any touch by mistake.
- Charging & Upgrading. Please always use high-rate 21700/18650 battery.
And make sure you are priming the coil well, and leaving a new coil to soak for a while before use. You can also try poking the wick hole with a needle/wire. If you have another spare coil, drip a bit of liquid in the juice wick slots, install it, fill up your tank and just give it a couple of minutes.
Now that your atomizer is primed you need to open up the top of your vape pen to install it. In order to open the Joyetech AIO you first must take note that it is a child-locked vape pen, so you will have to push down on the top ring while twisting it to the left.
To vape, turn the device on by pressing the fire button 5 times in quick succession, then hold the button while inhaling on the mouthpiece. The button light on the kit will flash 5 times to indicate that it is on. The AIO is turned off in the same way. Your Joyetech eGo AIO Kit comes with 2 coils.
To vape, turn the device on by pressing the fire button 5 times in quick succession, then hold the button while inhaling on the mouthpiece. The button light on the kit will flash 5 times to indicate that it is on. The AIO is turned off in the same way. Your Joyetech eGo AIO Kit comes with 2 coils.
To turn on the Exceed Grip, click the fire button five times. The fire button has a nice click to it. There's no screen on the Exceed Grip and there aren't any settings, so once it's on, all you have to do is press the firing button to vape. Joyetech made this really easy for beginners to use.
It is a great device for beginners and for those looking to quit smoking. It will also be a good option for those more experienced vapers looking for a portable stealth vape. If you are looking for your first vaping device then the Joyetech Ego AIO is a fantastic choice and comparable to Innokin's Endura T18.
Most USB outputs are fine to charge your vape, specifically USB outputs from computers, TVs, game consoles or car chargers. If you have a phone charger that you can use to plug your own USB cable into, that's the safest option. It's always best to use the same cable that came with your device to charge your vape.
Why your vape tastes burnt
It tastes burnt because the wick inside your atomizer coil has dried out and burned up when it was heated. If the wick is not fully saturated with eliquid when you take a puff, this material can char and leave a foul taste in your mouth. Vapers call this a 'dry hit. 'R200 to R400 Starter Kits - Joyetech Ego AIO ECO Starter Kit for only 150.00.
