Connect your soundbar and a device using HDMI
Make sure the TV, soundbar, and device are turned off. Then, connect one end of an HDMI cable into any HDMI port on your TV (make a note of which one). Next, connect the other end to the HDMI OUT port on your soundbar.When the remote is in receiver mode, the BD receiver button flashes orange. 2 Plug the power cable of the wireless receiver module into a working outlet, and then using a small pointed object (paper clip), press the ID Set button for 5 seconds. The blue Link LED will blink rapidly.
With Samsung Multiroom Link, you can easily set up a sound system that runs everywhere you want it to. Just add multiroom speakers and other compatible devices wherever you might want to listen to your music. Multiroom Link lets you create a complete and unified audio system that runs throughout your entire home.
Use Samsung's Dual Audio Feature
- Go to Settings > Connections > Bluetooth.
- In Android Pie, tap Advanced.
- Turn on the Dual Audio toggle switch.
- To use Dual Audio, pair the phone with two speakers, two headphones, or one of each, and audio will stream to both.
Reset the soundbar by powering it off and then pressing and holding the STOP button until it displays 'INIT OK'. Power on the soundbar, and then try pairing the soundbar to your TV again.
Samsung wam1500/za Owner's Manual
“Bluetooth is ready.” Turn on the Bluetooth function of your smart device, and then select Search. Select the [Samsung] R5, [Samsung] R3 or [Samsung] R1. The Bluetooth connection between the smart device and the WAM speaker is made.Wi-Fi SETUP / SPK ADD Connect to a wireless network (Wi-Fi) via the Samsung Multiroom app. When disconnecting the power cable from a wall outlet, pull the plug. Do not pull the cable. Do not connect this unit or other components to an AC outlet until all connections between components are complete.
Connection method 1: Connecting to a Wi-Fi network using the WPS button of a wireless router
- Disconnect the LAN cable from the speaker.
- Place the speaker near the wireless router.
- Set the Wi-Fi antenna on the rear in the upright position.
- Set the NETWORK OFF/ON switch on the rear of the speaker to ON.
- Press the Menu button on your TV remote.
- Navigate to Sound.
- Select Speaker Settings.
- Turn Add New Device on.
- Select Samsung Audio Device List.
- Select the device that you wish to pair.
From any Android Device
- Open the App Drawer. Newer versions of Android's operating system may not have the app drawer button.
- Go to Settings.
- Tap Bluetooth.
- Set the Bluetooth accessory in pairing/discovery mode.
- Ensure Bluetooth is On and then select your device from the list below.
If you want to connect your soundbar via Bluetooth, first switch the soundbar to pairing mode by pressing the Pair button on the soundbar's remote control. If you don't have the soundbar remote, don't worry. Just press the source button until the display says "BT."
1 Touch the MODE button on top of the speaker one or more times until you hear “Bluetooth is ready.” 2 Turn on the Bluetooth function of your smart device, and then select Search. 3 Select the [Samsung] R5, [Samsung] R3 or [Samsung] R1. The Bluetooth connection between the smart device and the WAM speaker is made.
NOTE ✓ To reset the speaker, touch and hold the Volume (-,+) button at the same time for 5 seconds. Mute icon Mute (from the App or by tapping in the Touch Area when TV SoundConnect is active.) the speaker to your network using the Wi-Fi Setup method. (Requires a smart device and the Samsung Multiroom app.)
Press the Home button on your Samsung Smart Control, to access the Home Screen. Using the directional pad on your remote, navigate to and select Settings. Select Sound Output to select your preferred sound output device. Select Bluetooth Audio to begin pairing your Bluetooth audio device.
Factory Reset
Press and hold the plus and minus volume buttons until a purple indicator begins to flash. The device should reset and reboot. If issues still persist, try updating the firmware once more after this reset.Power Off : Touch and hold anywhere in the Touch Area for 10 seconds. Touch the touch area to turn the speaker back on. To adjust the volume rapidly, touch and hold + or - key.
Factory Reset
You can try to reset the device to factory settings. Press and hold the plus and minus volume buttons until a purple indicator begins to flash. The device should reset and reboot.Manual connection
Use a small pointed object to press the ID SET button on the back of the subwoofer. Continue holding until STANDBY turns off and LINK (Blue LED) blinks quickly. While the soundbar is turned off, press and hold Mute on the remote control. Continue holding until ID SET appears on the soundbar's display.Press and hold PAIRING on the back of the wireless subwoofer for more than 5 seconds, until the led on the subwoofer blinks red and green alternating. Unplug the power cord of the soundbar and the wireless subwoofer. Connect them again after the LED of the main unit and the wireless subwoofer are fully turned off.
By using their iOS and Android app, you can figure out how to get the best sonic performance from their subwoofers. This sophisticated yet simple software can be used to fine-tune their DB Series subwoofers. All of this is done is by linking your phone to the speaker via a Bluetooth connection.
Press and hold PAIRING on the back of the wireless subwoofer for more than 5 seconds, until the led on the subwoofer blinks red and green alternating. Unplug the power cord of the soundbar and the wireless subwoofer. Connect them again after the LED of the main unit and the wireless subwoofer are fully turned off.
Connect the Soundbar to a Bluetooth® Device
- Press the Source button on the soundbar or remote until BT appears on the display.
- Set the soundbar to BT mode.
- Press and hold the Source button on the soundbar or remote.
- Continue holding until BT PAIRING appears on the display.
- Select the Bluetooth® device you want to connect.
Press and hold PAIRING on the back of the wireless subwoofer for more than 5 seconds, until the led on the subwoofer blinks red and green alternating. Unplug the power cord of the soundbar and the wireless subwoofer. Connect them again after the LED of the main unit and the wireless subwoofer are fully turned off.
The sound on your wireless subwoofer can drop out if there is interference or a physical obstruction between the soundbar and subwoofer. Make sure the subwoofer is within range of a good signal of your soundbar, and that the issue is not with the source audio.
Typically, you position a subwoofer along the front wall of the room. Moving all of the bass sounds to the subwoofer gives your front speakers the ability to focus on mid- and high-range frequencies. (The subwoofer can handle all the low-frequency bass sounds in a home theater.)
