If you know the correct setting, follow these steps:
- Shut down the computer and restart it.
- Start the BIOS or UEFI firmware setup program.
- Change the SATA setting to the correct value.
- Save settings and restart the computer.
- Select Start Windows Normally if prompted.
The BIOS settings are stored in the CMOS chip (which is kept powered up via the battery on the motherboard).
Common keys to enter the BIOS are F1, F2, F10, Delete, Esc, as well as key combinations like Ctrl + Alt + Esc or Ctrl + Alt + Delete, although those are more common on older machines. Also note that a key like F10 might actually launch something else, like the boot menu.
Check Your BIOS Version by Using the System Information Panel. You can also find your BIOS's version number in the System Information window. On Windows 7, 8, or 10, hit Windows+R, type “msinfo32” into the Run box, and then hit Enter. The BIOS version number is displayed on the System Summary pane.
Press the F10 key to exit the BIOS setup utility. In the Setup Confirmation dialog box, press the ENTER key to save the changes and exit.
BIOS, which stands for Basic Input Output System, is software stored on a small memory chip on the motherboard. The BIOS firmware is non-volatile, meaning that its settings are saved and recoverable even after power has been removed from the device.
Press the F10 key. You then might get a confirmation to exit BIOS. Select Yes if you do. Then your computer should reboot into Windows.
Opening the BIOS Setup Utility
- Turn off the computer and wait five seconds.
- Turn on the computer, and then immediately press the Esc key repeatedly until the Startup Menu opens.
- Press F10 to open the BIOS Setup Utility.
No need to update the BIOS when you're only adding or changing RAM. Indeed, "if it ain't broke don't fix it" is a good thing to remember where BIOS updates are concerned.
The UEFI firmware takes some time to initialize your computer hardware before your operating system boots up. However, if you see the Last BIOS Time over 25-30 seconds, it means that there's something wrong in your UEFI settings.
What are two examples of settings that can be changed in the BIOS setup program? (Choose two.)
- drive partition size.
- device drivers.
- swap file size.
- boot order.
- enabling and disabling devices. Explanation: The BIOS setup program is used to change settings if memory modules, storage devices, and adaptor cards are added.
BIOS uses the Master Boot Record (MBR) to save information about the hard drive data while UEFI uses the GUID partition table (GPT). The major difference between the two is that MBR uses 32-bit entries in its table which limits the total physical partitions to only 4.
Unified Extensible Firmware Interface (UEFI) is a specification for a software program that connects a computer's firmware to its operating system (OS). UEFI is expected to eventually replace BIOS. Like BIOS, UEFI is installed at the time of manufacturing and is the first program that runs when a computer is turned on.
Here's how it's done.
- Right click the Start menu and select Control Panel.
- Click Hardware and Sound.
- Select Power Options.
- Find Processor power management and open the menu for Minimum processor state.
- Change the setting for on battery to 100%.
- Change the setting for plugged in to 100%.
Clearing the CMOS on your motherboard will reset your BIOS settings to their factory defaults, the settings that the motherboard maker decided were the ones that most people would use. One reason to clear CMOS is to help troubleshoot or solve certain computer problems or hardware compatibility issues.
Resetting the bios shouldn't have any effect or damage your computer in any way. All it does is reset everything to it's default. As for your old CPU being frequency locked to what your old one was, it could be settings, or it could also be a CPU which is not (fully) supported by your current bios.
Performing a Factory Reset from BIOS. Press F2 immediately after pressing the power button and before the BIOS splash screen. You can press F2 repeatedly until the Configuration Utility starts. If the workstation boots into the operating system without starting the utility, restart the workstation and try again.
How to Restore a Computer to Factory Settings Using the F Key
- Press the power button to turn on the computer or reboot it if it's on already.
- Press and hold the "F8" key before the computer begins to boot if you only have one operating system loaded on your computer.
- Select "Repair Your Computer" using the up or down arrow key on the Advanced Boot Options screen that opens.
The steps are:
- Start the computer.
- Press and hold the F8 key.
- At Advanced Boot Options, choose Repair Your Computer.
- Press Enter.
- Select a keyboard language and click Next.
- If prompted, login with an administrative account.
- At the System Recovery Options, choose System Restore or Startup Repair (if this is available)
3 Steps to Reset BIOS Windows 10
You can click Start -> Power, press and hold Shift key, and click Restart button to reboot Windows into Windows Recovery Environment. Then click Troubleshoot -> Advanced Options -> UEFI Firmware Settings, and click Restart to enter into BIOS settings screen.Most often, resetting the BIOS will reset the BIOS to the last saved configuration, or resets your BIOS to the BIOS version that shipped with the PC. Sometimes the latter can cause issues if settings were changed to take account for changes in hardware or OS after install.
Method 2: Resetting the BIOS
- Shut off the power supply and wait 10 seconds.
- Press PC Power on button and PC Reset button all at the same time for about 10 seconds.
- Release the buttons thereafter and turn on the power supply on to start the PC as normal.
