Your device may not be paired correctly with the iBT230. Do so by making sure your Bluetooth device is fully charged. Turn on your Bluetooth device and make it "discoverable" by turning on Bluetooth mode (check in Options or Settings). Press and hold the Play/Pause/Pairing Button for 2 seconds.
Control for AndroidThe iHome Control app is the perfect way to control your iHome SmartPlug right from your Android device, from virtually anywhere in the world from your Android phone or tablet.
Resetting the UnitIf the unit is “frozen” or locks up, you may wish to reset it. To do so, turn the unit ON and press the end of paperclip or similar into the reset port on the back of the unit for less than 2 seconds to reset it without clearing Bluetooth settings. The unit will reset and power back on.
Press and hold the Power Button to turn on the iDM12 (release when green light appears). 3) Turn on Bluetooth functionality on your Bluetooth device. Typically, Bluetooth controls are found on the device's tools or settings menu (see your user manual). Turn on Bluetooth connectivity and make your device “discoverable”.
The iBT70 has two audio sources: Bluetooth wireless audio streaming from your mobile device (iPad, iPhone, iPod, Android, Windows smartphones) or direct line-in via the included cable and any device with a headphone jack.
1. Press and hold the Power Button to turn on the unit. The Bluetooth status indicator will glow solid blue when a linked device is in range and detected. You can then listen to audio streamed wirelessly from your paired Bluetooth device.
Press and hold the Bluetooth Pairing Button for 2 seconds. 3. Select “iHome iBT39” on device to pair. Once the iBT39 is paired to a device, it will attempt to autolink when the unit is turned on and when the device is within range (about 33 feet).
Press and hold the Bluetooth/Speakerphone Button for 2 seconds. The iBT74 will beep and the Bluetooth status indicator light on top of the unit will flash quickly. If Color Mode is on, the cabinet lights will flash blue and red.
Flashing blue can mean a bad connection somewhere (check to make sure the USB cable is firmly plugged in to the outlet adapter if you use a modular setup, that the cable itself isn't defective (swap cables to test), and that the connection to the base of the charger is firmly plugged in), a case that is interfering
If your phone is just a little off center, it won't charge. If you're using a wireless charger that holds a phone upright, the charging puck might be set too high or too low. In this case the charging coil isn't aligned properly. Sometimes the phone might be off to the side a little bit, also causing misalignment.
Charge wirelessly
- Connect your charger to power.
- Place the charger on a level surface or other location recommended by the manufacturer.
- Place your iPhone on the charger with the display facing up.
- Your iPhone should start charging a few seconds after you place it on your wireless charger.
Light Indicators Let You Know How Much Power Is Left . Simple To Use. Just Plug In Your Device, Hit The Side "On" Button, And Your Device Is Charging! To Turn Off The Power Bank, Simply Disconnect The Usb Cable Or Device.
The docks will charge your iPhone or iPod until completely charged then stop charging. Use both docks to charge two devices at once.
1. Press and hold the TIME button and SNOOZE together for 3 seconds, the display will flash. NOTE: If during the time set no key is pressed for 10 seconds, the previous time will be automatically stored.
Touch and release the Snooze/Display Dimmer Button to confirm Snooze setting. 2 beeps will sound. 4. While the alarm is sounding, touch and release the Snooze/Display Dimmer Button to temporarily silence the alarm for the set duration (9 minutes is the default).
Two beeps will sound. 2. Press the Snooze/Dimmer Button on the iBTW23 after the alarm sounds. The alarm will be silenced and will come on again in about 9 minutes (default).
When unit is ON but not charging (operating on battery, micro USB cable not connected) you can review the current battery status on the Battery Status Indicator Lights (four white LEDs on front of the unit above the iHome badge) any time a button is pressed.
If your device does not auto-link when within range, re-pair the device. To do so, first delete this unit from your Bluetooth devices menu. Move the Power OFF/Bluetooth/Aux Switch on the unit to the Bluetooth position (center) to begin pairing. Check your device's manual for details on Bluetooth pairing and linking.
Flashing red light - Power Bank is being charged. Solid red light - Power Bank is done being charged. To recharge your Power Bank plug the included micro USB cable into any USB power source (wall charger, car charger, etc.) until the LED light turns solid red.
The speaker volume is “low” or “inaudible.”Tap on the “Settings” icon 2. Under Bluetooth (devices), choose the iBT16 by clicking on the arrow. 3.
Listening to iPhone or iPodPress the Power Button (or any button) to turn the unit on. Press Play on iPhone or iPod to listen to music. Adjust levels with - or + Buttons. Press the DPS Button to activate Bongiovi audio.
